PRODUCTS

PRODUCTS

+
  • 20230717 (1).jpg

Inverter potting glue


Polyurethane potting compound GF-816-V

Category:

Inverter Potting Glue

Keywords:

Details

Details


1. Product introduction
GF-816-V is a two-component flame-retardant polyurethane circuit board sealant. This product meets the national environmental protection requirements, with transparent appearance, good waterproof and insulating properties. This product is mainly used in the protection of circuit boards, so as to play a role in shock prevention, moisture prevention and dust prevention.


2. Product features
1.The cured product is transparent, with high transparency and excellent gloss.
2.The product is endowed with the benefits of automatic defoaming and leveling, remarkable surface finish, minimal water ripple, and a simple operation process.
3.The curing speed is fast, and it has excellent weather resistance and ultraviolet resistance after curing, and it keeps good performance at the temperature of (-40℃~120℃).

 

3. Technical parameters

Before curing

project

GF-816-VA glue

GF-816-VB Glue

Exterior

light yellow transparent liquid

light yellow transparent liquid

Viscosity (CPS 25℃)

600±300

1000±300

Density (g/cm3)

0.98±0.05

1.1±0.05

Mixed viscosity (CPS 25℃)

800±300

mass mixing ratio

A:B=1:(1~1.05)

Operating time (min25℃)

25~40

Surface dry time (H 25℃)

4-6

Surface dry time (min 60℃)

15~20

Full curing time (H 25°C)

36~72H

after curing

project

unit or condition

cured product

Exterior

visual inspection

light yellow transparent solid

Test items

value

standard

Hardness Shore-A

40±5

GB/T531.1-2008

Water absorption (%)

<0.3

GB/T1034-2008

Tensile strength (Mpa)

≥0.4

GB/T528-2009

Elongation(%)

≥70

GB/T528-2009

Surface insulation resistance (ohm)

≥6.0*10 13

GB3859.1-93-T

Volume resistance (ohm-cm)

≥8.0*10 12

GB/T 1410-2006

Halogen content (PPM)

<900

EN14582:2007

Flammability rating

V0

UL94

 

4.  use and safety precautions
1. Weighing and mixing: This product is a two-component modified resin, and the mixing ratio is calculated by weight. The accurate mixing ratio is very important (excessive component A will cause the cured surface to be sticky, excessive component B will cause the bottom bubbling);
2. Stirring: When stirring, please stir slowly in the same direction to avoid a lot of air bubbles. Stir to ensure that A and B components are evenly mixed. Since component A is slightly turbid, there are still a lot of filaments with the naked eye when stirring, so it needs to be patiently stirred until it is completely transparent. If the mixing is uneven, it will cause stickiness and ripples on the rubber surface;
3. Blistering: The evenly stirred glue needs to be vacuumed and defoamed, or dripped with a machine; please do not use wooden sticks and other sticks with moisture to stir; 4
. Safety: Please try to prevent the skin from contacting with this product. If you accidentally touch it, please wash it with plenty of water or seek medical treatment;
5. Note: manual mixing will inevitably introduce air bubbles, and it needs to be vacuumed and degassed before dispensing. Due to the slow speed of manual dispensing, the requirements for environmental humidity are relatively high, and the relative humidity is preferably between 40 and 60. The base material should be dry, avoid using ink containing glycerin;
6. Pay attention to the preservation of unused glue after opening. The unused glue should be vacuumed or filled with dry nitrogen and sealed for storage. The reserved space in the container should not be too large to prevent the B glue from being turbid or the AB glue from absorbing moisture and causing the uncured or opaque glue block after curing. And the appearance of air bubbles in potting products.


5. Storage, transportation and precautions
1. Components A and B are put into airtight containers respectively, and stored separately in a dry, dark and cool place;
2. Such products are not dangerous goods and can be transported as general chemicals;
3. This product (especially component B) is easy to absorb water and deteriorate when placed in the air, so it should be kept sealed, and please seal it in time after use.

 

6.  packaging and shelf life
1. Packing: A: 200Kg/drum or 20Kg/drum B: 200Kg/or 20Kg/drum can be packed according to customer requirements;
2. Shelf life: under normal temperature conditions A: 6 months B: 6 months.

 

ONLINE MESSAGE

*Note: Please be sure to fill in the information accurately, and keep the communication unblocked, we will get in touch with you as soon as possible

The company mainly produces and operates solder paste, solder bars, solder wire, anode plates (rods), anode balls and other related electronic welding materials.

The company mainly produces and operates polyurethane potting adhesives, sealants, and structural adhesives.

Hong Kong Chengxing Group Co., Ltd.

Tel:(852)27954549

Add:The company mainly produces and operates polyurethane potting adhesives, sealants, and structural adhesives.

Gaoxin Tin Industry (Huizhou) Co., Ltd.

Tel:0752-6681186

Add: Xianan Industrial Zone, Yuanzhou Town, Boluo County, Guangdong Province

Kunshan Chengli Solder Manufacturing Co., Ltd.

Tel:0512-57875116

Add: No. 20-1 Zhuzhu Road, Lujia Town, Kunshan City, Jiangsu Province

Huizhou Chengli Industrial Co., Ltd.

Tel:0752-6805010

Add: G/F, Block B, Heli Industrial Center, 3-5 Wang Tai Road, Kowloon Bay, Hong Kong


Copyright © Kunshan Chengli Solder Manufacturing Co., Ltd.  Designed  By:www.300.cn  Business license